What are your thoughts and feelings on How to Install a Bathtub Yourself?
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately hard project. If the old tub is easily obtainable, the project can move immediately; if you need to open a wall to eliminate the old bathtub as well as position the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly need a helper to leave the old bathtub and also set in the new one. Make certain you have qualified yourself for the job and are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed project, it is better to consider using one prior to you begin. Chances are you may need an expert plumber to make tube connections.
This short article will certainly aid you mount a brand-new bath tub in your restroom if you have already bought a new bathtub and also do not need to change the arrangement of your previous water supply pipes.
Your tools as well as material list need to consist of the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of removing the existing faucets can be quite bothersome because of the restricted access that is often the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a cloth all set for the staying water that will originate from the pipes. Once the supply pipelines have been gotten rid of, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. As soon as the faucets have been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old sealing compound.
Before moving on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end offers a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin guaranteeing that the washing machines are in area between the faucet and the sink. Safeguard the tap in position with the manufacturer given backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type ought to be linked to the faucet ends first, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Using both wood boards under its feet, place the tub in the required setting. The wood boards are practical in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by checking the level and also readjusting the feet on the bathtub up until the level reviews level.
To mount faucets, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Switch on the supply of water as well as inspect all joints as well as brand-new pipework for leakages and also tighten them if required. Fill up the tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and securing around the bath tub needs to wait till the bath tub has actually been made use of at the very least when as this will settle it into its final setting.
Planning for the Installment
To start with, the sustaining structure provided with the bathroom should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last placement.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to crack an inflexible seal, triggering the water to pass through the wall between the bathroom as well as the tiling, leading to difficulties with moisture and feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked paper or soft rope. Remember to always load the bathtub with water prior to sealing, to enable the activity experienced when the tub is in use. The sealer can crack relatively very early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our piece on How to Install a Bathtub Yourself. Thank you for taking the time to read our post. Appreciated our posting? Please share it. Help another person check it out. Thanks a lot for your time. Please check our site back soon.
Get Your Estimate Now